Standard Svensk standard · SS-EN ISO 15875-2:2025

Plaströrsystem för varm- och kallvatteninstallationer – Tvärbunden polyeten (PE-X) – Del 2: Rör (ISO 15875-2:2025, IDT)

Status: Gällande

Köp denna standard

Standard Svensk standard · SS-EN ISO 15875-2:2025

Plaströrsystem för varm- och kallvatteninstallationer – Tvärbunden polyeten (PE-X) – Del 2: Rör (ISO 15875-2:2025, IDT)
Prenumerera på standarden - Läs mer Dölj
Pris: 1 220 SEK
standard ikon pdf

PDF

Pris: 1 220 SEK
standard ikon

Papper

Pris: 1 952 SEK
standard ikon pdf + standard ikon

PDF + papper

Fler alternativ Färre alternativ
Provläs denna standard
Omfattning
This document specifies the characteristics of pipes for crosslinked polyethylene (PE-X) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for human consumption (domestic systems), and for heating systems, under design pressures and temperatures according to the class of application (see ISO 15875-1).




It also specifies the test parameters for the test methods referred to in this document.

The designation crosslinked polyethylene is used together with the abbreviation PE-X throughout this document. ISO 15875 covers a range application classes, design pressures and pipe dimension classes. For values of design temperature (TD), maximum temperature (Tmax) and malfunction temperature (Tmal) and service times in excess of those defined in ISO 15875-1, this document does not apply.




NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these application classes (see ISO 15875-1), taking into account their particular requirements and any relevant national regulations and installation practices or codes. The ISO 15875 standards series is a piping system standard.

This document shall only be used in conjunction with all the other parts of ISO 15875. This document is applicable to PE-X pipes for hot and cold water installations, which are intended to be connected to fittings conforming to ISO 15875-3, whereby the joints conform to the requirements of ISO 15875-5. It is applicable to PE-X pipes with and without barrier layer.




NOTE 2 In the case of PE-X pipes provided with a thin barrier layer, e.g. to prevent or greatly diminish the diffusion of gases and the transmission of light through the pipe wall, the design stress requirements are totally met by the base PE-X pipe. In order to comply with this standard, all requirements of this document shall be met.




NOTE 3 The test results obtained from a specific piping system test according to ISO 15875-5 cannot be transferred to other combinations of pipes and fittings

Ämnesområden

Rör Allmänt (23.040.01) Gummi- och plastprodukter Allmänt (83.140.01) Plaströr och plaströrskomponenter ej avsedda för vätska (83.140.30) Byggnadsdelar (91.060)


Köp denna standard

Standard Svensk standard · SS-EN ISO 15875-2:2025

Plaströrsystem för varm- och kallvatteninstallationer – Tvärbunden polyeten (PE-X) – Del 2: Rör (ISO 15875-2:2025, IDT)
Prenumerera på standarden - Läs mer Dölj
Pris: 1 220 SEK
standard ikon pdf

PDF

Pris: 1 220 SEK
standard ikon

Papper

Pris: 1 952 SEK
standard ikon pdf + standard ikon

PDF + papper

Fler alternativ Färre alternativ

Produktinformation

Språk: Engelska

Framtagen av: Plaströrssystem, SIS/TK 156/AG 02

Internationell titel: Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 2: Pipes (ISO 15875-2:2025, IDT)

Artikelnummer: STD-82099573

Utgåva: 2

Fastställd: 2025-10-29

Antal sidor: 37

Ersätter: SS-EN ISO 15875-2:2004 , SS-EN ISO 15875-2:2004/A1:2007 , SS-EN ISO 15875-2:2004/A2:2020